Nitric acid

Nitric acid
Identifiers
CAS number 7697-37-2 Y
PubChem 944
ChemSpider 919 Y
UNII 411VRN1TV4 Y
EC number 231-714-2
UN number 2031
KEGG D02313 Y
MeSH Nitric+acid
ChEBI CHEBI:48107 Y
ChEMBL CHEMBL1352 Y
RTECS number QU5775000
Gmelin Reference 1576
3DMet B00068
Jmol-3D images Image 1
Image 2
Properties
Molecular formula HNO3
Molar mass 63.01 g mol−1
Exact mass 62.995642903 g mol-1
Appearance Colorless liquid
Density 1.5129 g cm-3
Melting point

-42 °C, 231 K, -44 °F

Boiling point

83 °C, 356 K, 181 °F (68% solution boils at 121 °C)

Solubility in water Completely miscible
Acidity (pKa) -1.4
Refractive index (nD) 1.397 (16.5 °C)
Dipole moment 2.17 ± 0.02 D
Hazards
MSDS ICSC 0183
PCTL Safety Website
EU Index 007-004-00-1
EU classification C O
R-phrases R8 R35
S-phrases (S1/2) S23 S26 S36 S45
NFPA 704
0
4
0
OX
Flash point Non-flammable
Related compounds
Other anions Nitrous acid
Other cations Sodium nitrate
Potassium nitrate
Ammonium nitrate
Related compounds Dinitrogen pentoxide
 Y (verify) (what is: Y/N?)
Except where noted otherwise, data are given for materials in their standard state (at 25 °C, 100 kPa)
Infobox references

Nitric acid (HNO3), also known as aqua fortis and spirit of nitre, is a highly corrosive and toxic strong mineral acid which is normally colorless but tends to acquire a yellow cast due to the accumulation of oxides of nitrogen if long-stored. Ordinary nitric acid has a concentration of 68%.[1] When the solution contains more than 86% of it, it is referred to as fuming nitric acid. Depending on the amount of nitrogen dioxide present, fuming nitric acid is further characterized as white fuming nitric acid or red fuming nitric acid, at concentrations above 95%. Nitric acid is also commonly used as a strong oxidizing agent.

Contents

Physical and chemical properties

Pure anhydrous nitric acid (100%) is a colorless mobile liquid with a density of 1.512 g/cm3 which solidifies at −42 °C to form white crystals and boils at 83 °C. When boiling in light, and slowly even at room temperature, there is a partial decomposition with the formation of nitrogen dioxide following the reaction:

4 HNO3 → 2 H2O + 4 NO2 + O2

Thus, anhydrous nitric acid should be stored below 0 °C to avoid decomposition. The nitrogen dioxide (NO2) remains dissolved in the nitric acid coloring it yellow, or red at higher temperatures. While the pure acid tends to give off white fumes when exposed to air, acid with dissolved nitrogen dioxide gives off reddish-brown vapors, leading to the common name "red fuming acid" or "fuming nitric acid". Fuming nitric acid is also referred to as 16 molar nitric acid. It is the most concentrated form of nitric acid at Standard Temperature and Pressure (STP).

Nitric acid is miscible with water and distillation gives a maximum-boiling azeotrope with a concentration of 68% HNO3 and a boiling temperature of 120.5 °C at 1 atm, which is the ordinary concentrated nitric acid of commerce. Two solid hydrates are known; the monohydrate (HNO3·H2O) and the trihydrate (HNO3·3H2O).

Nitrogen oxides (NOx) are soluble in nitric acid and this property influences more or less all the physical characteristics depending on the concentration of the oxides. These mainly include the vapor pressure above the liquid and the boiling temperature, as well as the color mentioned above.

Nitric acid is subject to thermal or light decomposition with increasing concentration and this may give rise to some non-negligible variations in the vapor pressure above the liquid because the nitrogen oxides produced dissolve partly or completely in the acid.

Acid-base properties

Nitric acid is normally considered to be a strong acid at ambient temperatures. There is some disagreement over the value of the acid dissociation constant, though the pKa value is usually reported as less than –1. This means that the nitric acid in solution is fully dissociated except in extremely acidic solutions. The pKa value rises to 1 at a temperature of 250 °C.[2]

Nitric acid can act as a base with respect to an acid such as sulfuric acid.

HNO3 + 2H2SO4 NO2+ + H3O+ + 2HSO4; K ~ 22

The nitronium ion, NO2+, is the active reagent in aromatic nitration reactions. Since nitric acid has both acidic and basic properties it can undergo an autoprotolysis reaction, similar to the self-ionization of water

2HNO3 NO2+ + NO3 + H2O

Reactions with metals and strong oxidizing properties

Nitric acid reacts with most metals. This characteristic has made it a common agent to be used in acid tests.

Very dilute nitric acid acts as a typical acid to react with active metals. For example, strongly electropositive metals, such as magnesium react with nitric acid as with other acids, reducing hydrogen.

Mg + 2 H+ → Mg2+ + H2

However, both dilute and concentrated nitric acid is a strong oxidizing agent as shown by its large positive reduction potential (E0r) and does not react with metals in the same way as most other acids. Nitrogen monoxide is reduced from the dilute acid reacting with metals while nitrogen dioxide is reduced from the concentrated one. Hydrogen is not evolved.

NO3- + 2 H+ +    e- → NO2 +   H2O,     E0r = 0.79 V
NO3- + 4 H+ + 3 e- → NO  + 2 H2O,     E0r = 0.96 V

Nitric acid can oxidize non-active metals such as copper and silver. With these non-active or less electropositive metals the products depend on temperature and the acid concentration. For example, copper reacts with dilute nitric acid at ambient temperatures with a 3:8 stoichiometry.

3 Cu + 8 HNO3 → 3 Cu2+ + 2 NO + 4 H2O + 6 NO3-

The nitric oxide produced may react with atmospheric oxygen to give nitrogen dioxide. With more concentrated nitric acid, nitrogen dioxide is produced directly in a reaction with 1:4 stoichiometry.

Cu + 4 H+ + 2 NO3 → Cu2+ + 2 NO2 + 2 H2O

Some precious metals, such as pure gold do not react with nitric acid, though pure gold does react with aqua regia, a mixture of concentrated nitric acid and hydrochloric acid. However, some less noble metals (Ag, Cu, ...) present in some gold alloys relatively poor in gold such as colored gold can be easily oxidized and dissolved by nitric acid, leading to colour changes of the gold-alloy surface. Nitric acid is used as a cheap means in jewelry shops to quickly spot low-gold alloys (< 14 carats) and to rapidly assess the gold purity.

Being a powerful oxidizing agent, nitric acid reacts violently with many non-metallic compounds and the reactions may be explosive. Depending on the acid concentration, temperature and the reducing agent involved, the end products can be variable. Reaction takes place with all metals except the noble metals series and certain alloys. As a general rule, oxidizing reactions occur primarily with the concentrated acid, favoring the formation of nitrogen dioxide (NO2).

Reactions with non-metals

Being a powerful oxidizing acid, nitric acid reacts violently with many organic materials and the reactions may be explosive.

Reaction with non-metallic elements, with the exceptions of nitrogen, oxygen, noble gases, silicon and halogens, usually oxidizes them to their highest oxidation states as acids with the formation of nitrogen dioxide for concentrated acid and nitric oxide for dilute acid.

C + 4 HNO3 → CO2 + 4 NO2 + 2 H2O

or

3 C + 4 HNO3 → 3 CO2 + 4 NO + 2 H2O

Passivation

Although chromium (Cr), iron (Fe) and aluminium (Al) readily dissolve in dilute nitric acid, the concentrated acid forms a metal oxide layer that protects the metal from further oxidation, which is called passivation. Typical passivation concentrations range from 18% to 22% by weight.

Xanthoproteic test

Nitric acid reacts with proteins to form yellow nitrated products. This reaction is known as the xanthoproteic reaction. This test is carried out by adding concentrated nitric acid to the substance being tested, and then heating the mixture. If proteins are present that contains amino acids with aromatic rings, the mixture turns yellow. Upon adding a strong base such as liquid ammonia, the color turns orange. These color changes are caused by nitrated aromatic rings in the protein.[3][4] Xanthoproteic acid is formed when the acid contacts epithelial cells and is indicative of inadequate safety precautions when handling nitric acid.

Grades

The concentrated nitric acid of commerce consists of the maximum boiling azeotrope of nitric acid and water. Technical grades are normally 68% HNO3,[1] (approx 15 molar), while reagent grades are specified at 70% HNO3. The density of concentrated nitric acid is 1.42 g/mL. An older density scale is occasionally seen, with concentrated nitric acid specified as 42° Baumé.[5]

White fuming nitric acid, also called 100% nitric acid or WFNA, is very close to anhydrous nitric acid. One specification for white fuming nitric acid is that it has a maximum of 2% water and a maximum of 0.5% dissolved NO2. Anhydrous nitric acid has a density of 1.513 g/mL and has the approximate concentration of 24 molar.

A commercial grade of fuming nitric acid, referred to in the trade as "strong nitric acid" contains 90% HNO3 and has a density of 1.50 g/mL. This grade is much used in the explosives industry. It is not as volatile nor as corrosive as the anhydrous acid and has the approximate concentration of 21.4 molar.

Red fuming nitric acid, or RFNA, contains substantial quantities of dissolved nitrogen dioxide (NO2) leaving the solution with a reddish-brown color. One formulation of RFNA specifies a minimum of 17% NO2, another specifies 13% NO2. Because of the dissolved nitrogen dioxide, the density of red fuming nitric acid is lower at 1.490 g/mL.

An inhibited fuming nitric acid (either IWFNA, or IRFNA) can be made by the addition of 0.6 to 0.7% hydrogen fluoride (HF). This fluoride is added for corrosion resistance in metal tanks. The fluoride creates a metal fluoride layer that protects the metal.

Industrial production

Nitric acid is made by reaction of nitrogen dioxide (NO2) with water.

3 NO2 + H2O → 2 HNO3 + NO

Normally, the nitric oxide produced by the reaction is reoxidized by the oxygen in air to produce additional nitrogen dioxide.

Bubbling nitrogen dioxide through hydrogen peroxide can help to improve acid yield.

2 NO2 + H2O2 → 2 HNO3

Almost pure nitric acid can be made by adding sulfuric acid to a nitrate salt, and heating the mixture with an oil bath. A condenser is used to condense the nitric acid fumes that bubble out of the solution.

2 NaNO3 + H2SO4 → 2 HNO3 + Na2SO4

Dilute nitric acid may be concentrated by distillation up to 68% acid, which is a maximum boiling azeotrope containing 32% water. In the laboratory, further concentration involves distillation with either sulfuric acid or magnesium nitrate which act as dehydrating agents. Such distillations must be done with all-glass apparatus at reduced pressure, to prevent decomposition of the acid. Industrially, strong nitric acid is produced by dissolving additional nitrogen dioxide in 68% nitric acid in an absorption tower.[6] Dissolved nitrogen oxides are either stripped in the case of white fuming nitric acid, or remain in solution to form red fuming nitric acid. More recently, electrochemical means have been developed to produce anhydrous acid from concentrated nitric acid feedstock.[7]

Commercial grade nitric acid solutions are usually between 52% and 68% nitric acid. Production of nitric acid is via the Ostwald process, named after German chemist Wilhelm Ostwald. In this process, anhydrous ammonia is oxidized to nitric oxide, in the presence of platinum or rhodium gauge catalyst at a high temperature of about 500K and a pressure of 9 bar.

4 NH3 (g) + 5 O2 (g) → 4 NO (g) + 6 H2O (g) (ΔH = −905.2 kJ)

Nitric oxide is then reacted with oxygen in air to form nitrogen dioxide.

2 NO (g) + O2 (g) → 2 NO2 (g) (ΔH = −114 kJ/mol)

This is subsequently absorbed in water to form nitric acid and nitric oxide.

3 NO2 (g) + H2O (l) → 2 HNO3 (aq) + NO (g) (ΔH = −117 kJ/mol)

The nitric oxide is cycled back for reoxidation. Alternatively, if the last step is carried out in air:

4 NO2 (g) + O2 (g) + 2 H2O (l) → 4 HNO3 (aq)

The aqueous HNO3 obtained can be concentrated by distillation up to about 68% by mass. Further concentration to 98% can be achieved by dehydration with concentrated H2SO4. By using ammonia derived from the Haber process, the final product can be produced from nitrogen, hydrogen, and oxygen which are derived from air and natural gas as the sole feedstocks.[8]

Prior to the introduction of the Haber process for the production of ammonia in 1913, nitric acid was produced using the Birkeland–Eyde process, also known as the arc process. This process is based upon the oxidation of atmospheric nitrogen by atmospheric oxygen to nitric oxide at very high temperatures. An electric arc was used to provide the high temperatures, and yields of up to 4% nitric oxide were obtained. The nitric oxide was cooled and oxidized by the remaining atmospheric oxygen to nitrogen dioxide, and this was subsequently absorbed in dilute nitric acid. The process was very energy intensive and was rapidly displaced by the Ostwald process once cheap ammonia became available.

Laboratory synthesis

In laboratory, nitric acid can be made from copper(II) nitrate or by reaction of approximately equal masses of a nitrate salt with 96% sulfuric acid (H2SO4), and distilling this mixture at nitric acid's boiling point of 83 °C until only a white crystalline mass, a metal sulfate, remains in the reaction vessel. The red fuming nitric acid obtained may be converted to the white nitric acid.

H2SO4 + NO
3
HSO
4
(s) + HNO3(g)

The dissolved NOx are readily removed using reduced pressure at room temperature (10-30 min at 200 mmHg or 27 kPa) to give white fuming nitric acid. This procedure can also be performed under reduced pressure and temperature in one step in order to produce less nitrogen dioxide gas.

Uses

The main use of nitric acid is for the production of fertilizers; other important uses include the production of explosives, etching and dissolution of metals, especially as a component of aqua regia for the purification and extraction of gold, and in chemical synthesis.

Rocket fuel

Nitric acid has been used in various forms as the oxidizer in liquid-fueled rockets. These forms include red fuming nitric acid, white fuming nitric acid, mixtures with sulfuric acid, and these forms with HF inhibitor.[9] IRFNA (inhibited red fuming nitric acid) was one of 3 liquid fuel components for the BOMARC missile.[10]

Chemical reagent

In elemental analysis by ICP-MS, ICP-AES, GFAA, and Flame AA, dilute nitric acid (0.5 to 5.0 %) is used as a matrix compound for determining metal traces in solutions.[11] Ultrapure trace metal grade acid is required for such determination, because small amounts of metal ions could affect the result of the analysis.

It is also typically used in the digestion process of turbid water samples, sludge samples, solid samples as well as other types of unique samples which require elemental analysis via ICP-MS, ICP-OES, ICP-AES, GFAA and flame atomic absorption spectroscopy. Typically these digestions use a 50% solution of the purchased HNO3 mixed with Type 1 DI Water.[12]

In organic synthesis, nitric acid may be used to introduce the nitro group. When used with sulfuric acid, it generates the nitronium ion, which electrophilically reacts with aromatic compounds such as benzene.

In electrochemistry, nitric acid is used as a chemical doping agent for organic semiconductors, and in purification processes for raw carbon nanotubes.

Woodworking

In a low concentration (approximately 10%), nitric acid is often used to artificially age pine and maple. The color produced is a grey-gold very much like very old wax or oil finished wood (wood finishing).[13]

Other uses

A solution of nitric acid and alcohol, Nital, is used for etching of metals to reveal the microstructure. ISO 14104 is one of the standards detailing this well known procedure.

Commercially available aqueous blends of 5-30% nitric acid and 15-40% phosphoric acid are commonly used for cleaning food and dairy equipment primarily to remove precipitated calcium and magnesium compounds (either deposited from the process stream or resulting from the use of hard water during production and cleaning). The phosphoric acid content helps to passivate ferrous alloys against corrosion by the dilute nitric acid.

Safety

Nitric acid is a strong acid and a powerful oxidizing agent. The major hazard posed by it is chemical burn as it carries out acid hydrolysis with proteins (amide) and fats (ester) and decomposes animals' muscles. Concentrated nitric acid attacks tissues readily and stains human skin yellow due to its reaction with the keratin. These yellow stains turn orange when neutralized. [14] Systemic effects are unlikely, however, and the substance is not considered a carcinogen or mutagen.[15]

The standard first aid treatment for acid spills on the skin is, as for other corrosive agents, irrigation with large quantities of water. Washing is continued for at least ten to fifteen minutes to cool the tissue surrounding the acid burn and to prevent secondary damage. Contaminated clothing is removed immediately and the underlying skin washed thoroughly.

Being a strong oxidizing agent, reactions of nitric acid with compounds such as cyanides, carbides, metallic powders can be explosive and those with many organic compounds, such as turpentine, are violent and hypergolic (i.e. self-igniting). Hence, it should be stored away from bases and organics.

History

The first mention of nitric acid is in Pseudo-Geber´s De Inventione Veritatis, wherein it is obtained by calcining a mixture of niter, alum and blue vitriol. It was again described by Albert the Great in the 13th century and by Ramon Lull, who prepared it by heating niter and clay and called it "eau forte" (aqua fortis).[16]

Glauber devised the process still used today to obtain it, namely by heating niter with strong sulfuric acid. In 1776 Lavoisier showed that it contained oxygen, and in 1785 Henry Cavendish determined its precise composition and showed that it could be synthesized by passing a stream of electric sparks through moist air.[16]

References

  1. ^ a b "Technical Nitric acid". http://hk.wrs.yahoo.com/_ylt=Axt7wK9PI.NOPwQA_LSzygt.;_ylu=X3oDMTE1MnVpcGRuBHNlYwNzcgRwb3MDMTUEY29sbwNoazIEdnRpZANoa2MwMDlfNzQ-/SIG=14g278i5i/EXP=1323537359/**http%3a//www.skwp.de/data/8adbae81be94bae5c3d4a29ebed47bb09c9ab9c59eddb6cdbbae9dc2c799a9d78acbaab5bc95d8a2c2d4aea2c39e8b83.pdf. 
  2. ^ IUPAC SC-Database A comprehensive database of published data on equilibrium constants of metal complexes and ligands
  3. ^ Sherman, Henry Clapp (2007). Methods of organic analysis. Read Books. p. 315. ISBN 1408628023. 
  4. ^ Knowles, Frank (2007). A practical course in agricultural chemistry. Read Books. p. 76. ISBN 1406745839. 
  5. ^ Dean, John (1992). Lange's Handbook of Chemistry (14 ed.). McGraw-Hill. pp. 2.79–2.80. ISBN 0070161941. 
  6. ^ Urbanski, Tadeusz (1965). Chemistry and technology of explosives. Oxford: Pergamon Press. pp. 85–86. ISBN 978-0-08-010239-9. 
  7. ^ US 6200456 
  8. ^ Considine, Douglas M., ed (1974). Chemical and process technology encyclopedia. New York: McGraw-Hill. pp. 769–72. ISBN 978-0-07-012423-3. 
  9. ^ Clark, John D. Ignition!. ISBN 0-8135-0725-1. 
  10. ^ "BOMARC Summary". BILLONY.COM. http://www.techbastard.com/missile/bomarc/summary.php. Retrieved 2009-05-28. 
  11. ^ Franson, Mary A. H., Clesceri Lenore S., Greenberg Arnold E., Eaton Andrew D., ed (1998). Standard methods for the examination of water and wastewater (20th ed.). American Public Health Association, American Water Works Association, Water Environment Federation. ISBN 978-0-87553-235-6. 
  12. ^ EPA Method 200.8
  13. ^ Jewitt, Jeff (1997). Hand-applied finishes (illustrated ed.). Taunton Press. ISBN 978-1-56158-154-2. http://books.google.com/?id=CMJvfh2IUSYC. Retrieved 2009-05-28. 
  14. ^ Paul, May (November 2007). "Nitric acid". http://www.chm.bris.ac.uk/motm/nitric/nitrich.htm. Retrieved 2009-05-28. 
  15. ^ "Nitric acid: Toxicological overview". Health Protection Agency. http://www.hpa.org.uk/webc/HPAwebFile/HPAweb_C/1194947355794. Retrieved 2011-12-07. 
  16. ^ a b Encyclopædia Britannica 1911 edition, Nitric Acid

External links